Bowers & Wilkins Px7 S3 EQ settings for Mac

Measured EQ correction for the Bowers & Wilkins Px7 S3, the specs that matter, and what changes when you use them with a Mac. Copy the settings and apply them in one click.

The short answer

  • Lowers the bass below 200 Hz by about 4.5 to 8.5 dB, most near 100 Hz.
  • Adds about 2.5 to 5 dB from 1.5 to 3.5 kHz, most near 2.5 kHz.
  • Adds about 2.5 to 3.5 dB around 5.5 kHz.
  • Lowers the treble from 9 kHz up by about 2 to 3 dB.
Get the exact values

Px7 S3 at a glance

Wireless over-ear headphones with ANC and bio-cellulose drivers, released in 2025. Official specifications from Bowers & Wilkins:

Driver
40 mm bio-cellulose dynamic
Bluetooth
5.3
Battery
Up to 30 h; 15-min charge ≈ 7 h
Weight
300 g

Sources: Bowers & Wilkins: Px7 S3.

Using the Px7 S3 with a Mac

Codec: AAC, not aptX, aptX HD, aptX Adaptive or aptX Lossless. The Px7 S3 support SBC, AAC, aptX, aptX HD, aptX Adaptive and aptX Lossless, but macOS doesn't support aptX, aptX HD, aptX Adaptive or aptX Lossless. On a Mac they play over AAC, which carries the full 20 Hz to 20 kHz range at standard sample rates (44.1 or 48 kHz).

Calls sound worse than music. As soon as an app uses the headphones' microphone (Zoom, FaceTime, a dictation shortcut), Bluetooth switches to hands-free mode, which has much lower audio quality. Pick your Mac's built-in microphone as the input to keep the Px7 S3 in stereo music mode.

Multipoint. Connects to two devices at once; on a Mac, AAC is used regardless of the second device.

AAC on Mac The Px7 S3 supports aptX Adaptive for Android. macOS doesn't support aptX, so on a Mac the headphones connect over AAC.

Noise control without your phone. Bowers & Wilkins' app only runs on phones. TuningMac shows the Px7 S3's own noise control choices in your Mac's menu bar, such as Noise Cancellation, Pass-Through or Auto, depending on the model. It recognises your model even if you've renamed your headphones, and only ever connects to your own pair. How it works

What the measurements show

This correction comes from AutoEQ, based on Kuulokenurkka's measurements of the Px7 S3. It shows how much to boost or cut at each frequency to bring the headphones closer to AutoEQ's neutral target:

−12 dB−6 dB+6 dB+12 dB20501002005001k2k5k10k20k
EQ correction for the Bowers & Wilkins Px7 S3 (AutoEQ, Kuulokenurkka measurement). Above the line is a boost, below is a cut.
  • Lowers the bass below 200 Hz by about 4.5 to 8.5 dB, most near 100 Hz.
  • Adds about 2.5 to 5 dB from 1.5 to 3.5 kHz, most near 2.5 kHz.
  • Adds about 2.5 to 3.5 dB around 5.5 kHz.
  • Lowers the treble from 9 kHz up by about 2 to 3 dB.

Measured with noise cancelling on, in the first of several head positions Kuulokenurkka measured. How the headphones sit changes the result, so adjust by ear.

Fit, ear pads and your own ears all change what you hear, and neutral isn't everyone's favourite sound. Use this as a starting point, then adjust by ear.

Apply it in TuningMac (parametric EQ)

TuningMac's Advanced EQ imports this format directly. Copy the settings, then:

  1. Open TuningMac ▸ Settings ▸ Advanced EQ with your Px7 S3 connected.
  2. Turn on Use Advanced EQ for Px7 S3 (or whatever you've named them on your Mac).
  3. Choose More ▸ Paste from Clipboard.

TuningMac saves it for your Px7 S3 and loads it whenever they connect.

ParametricEQ.txt (Equalizer APO / AutoEQ format)
Preamp: -5.3 dB
Filter 1: ON LSC Fc 105 Hz Gain -3.7 dB Q 0.70
Filter 2: ON PK Fc 109 Hz Gain -6.8 dB Q 0.60
Filter 3: ON PK Fc 2247 Hz Gain 5.4 dB Q 1.21
Filter 4: ON PK Fc 487 Hz Gain 2.0 dB Q 1.54
Filter 5: ON PK Fc 59 Hz Gain 2.8 dB Q 3.27
Filter 6: ON HSC Fc 10000 Hz Gain -2.9 dB Q 0.70
Filter 7: ON PK Fc 9672 Hz Gain -2.2 dB Q 2.07
Filter 8: ON PK Fc 5411 Hz Gain 3.4 dB Q 5.11
Filter 9: ON PK Fc 1674 Hz Gain -1.0 dB Q 6.00
Filter 10: ON PK Fc 7971 Hz Gain 1.5 dB Q 4.76

Tune your Px7 S3 on your Mac

Download for Mac
#TypeFrequencyGainQ
1Low Shelf105 Hz−3.7 dB0.70
2Bell109 Hz−6.8 dB0.60
3Bell2.25 kHz+5.4 dB1.21
4Bell487 Hz+2.0 dB1.54
5Bell59 Hz+2.8 dB3.27
6High Shelf10 kHz−2.9 dB0.70
7Bell9.67 kHz−2.2 dB2.07
8Bell5.41 kHz+3.4 dB5.11
9Bell1.67 kHz−1.0 dB6.00
10Bell7.97 kHz+1.5 dB4.76

Preamp: −5.3 dB. It lowers the overall level so the boosts don't clip.

Prefer simple sliders? The 10-band version

No Advanced EQ needed: AutoEQ also gives values for a standard 10-band equalizer, the same bands as TuningMac's main EQ. In the menu bar popover choose Custom, set each slider, and set the preamp to about −5.0 dB.

31
−4.8
62
−4.3
125
−7.6
250
−1.6
500
+1.6
1k
0.0
2k
+4.7
4k
+1.9
8k
−0.5
16k
−6.9

Values in dB, at 31 Hz to 16 kHz. The parametric version above is more precise.

Questions

Which codec do the Bowers & Wilkins Px7 S3 use on a Mac?+

AAC. The Px7 S3 support SBC, AAC, aptX, aptX HD, aptX Adaptive and aptX Lossless, but macOS doesn't support aptX, aptX HD, aptX Adaptive or aptX Lossless, so on a Mac they play over AAC. That carries 20 Hz to 20 kHz audio at standard sample rates.

What are the best EQ settings for the Bowers & Wilkins Px7 S3?+

AutoEQ's correction, based on Kuulokenurkka's measurements, lowers the bass below 200 Hz by up to 8.5 dB, adds up to 5 dB from 1.5 to 3.5 kHz and lowers the treble from 9 kHz up by up to 3 dB, with a preamp of -5.3 dB. The exact values are on this page, ready to copy. Treat it as a neutral starting point and adjust to taste.

Why do my Bowers & Wilkins Px7 S3 sound bad on calls on a Mac?+

When an app uses the headphones' microphone, Bluetooth switches from stereo music mode to a hands-free call mode with much lower audio quality. To keep music quality during calls, choose your Mac's built-in microphone as the input instead. TuningMac's Input list does this in one click, and its Device Info shows which mode you're in.

Can I control the Bowers & Wilkins Px7 S3's noise cancelling from a Mac?+

Bowers & Wilkins' app only runs on phones. TuningMac shows the Px7 S3's own noise control choices in your Mac's menu bar, such as Noise Cancellation, Pass-Through or Auto, depending on the model. It recognises your model even if you've renamed your headphones, and only ever connects to your own pair.

Should I turn off the EQ in Bowers & Wilkins' app?+

For the most accurate result, yes. An equalizer set in Bowers & Wilkins' app is applied inside the headphones, so it also affects your Mac and would add to this correction. TuningMac's EQ only changes sound from your Mac, so it won't affect your phone.

Tune your Px7 S3 on your Mac

Parametric and 10-band EQ, noise control and battery in the menu bar.

Download for Mac

EQ data from AutoEQ by Jaakko Pasanen (MIT licence), measurement by Kuulokenurkka. Specifications from Bowers & Wilkins' published specifications. Bowers & Wilkins Px7 S3 is a trademark of Bowers & Wilkins; TuningMac is not affiliated with Bowers & Wilkins.