Shure SE112 EQ settings for Mac
Measured EQ correction for the Shure SE112, the specs that matter, and what changes when you use them with a Mac. Copy the settings and apply them in one click.
The short answer
- Cuts about 10 dB around 4.6 kHz.
- Adds about 7 dB around 6.8 kHz.
- Cuts about 6 dB around 180 Hz.
- Adds about 5 dB of high shelf above 10 kHz.
SE112 at a glance
Single dynamic-driver IEM. Official specifications from Shure:
- Impedance
- 16 ohms
- Sensitivity
- 102 dB SPL/mW
- Cable
- Fixed cable
Sources: Shure: SE112 product page.
Using the SE112 with a Mac
Wired, so no Bluetooth codec. The SE112 connect with a cable, so nothing is compressed on the way: plug them into the Mac's headphone jack, or a USB-C adapter or DAC.
Calls sound worse than music. As soon as an app uses the earbuds' microphone (Zoom, FaceTime, a dictation shortcut), Bluetooth switches to hands-free mode, which has much lower audio quality. Pick your Mac's built-in microphone as the input to keep the SE112 in stereo music mode.
What the measurements show
This correction comes from AutoEQ, based on oratory1990's measurements of the SE112. It shows how much to boost or cut at each frequency to bring the earbuds closer to AutoEQ's neutral target:
- Cuts about 10 dB around 4.6 kHz.
- Adds about 7 dB around 6.8 kHz.
- Cuts about 6 dB around 180 Hz.
- Adds about 5 dB of high shelf above 10 kHz.
Fit, ear tips and your own ears all change what you hear, and neutral isn't everyone's favourite sound. Use this as a starting point, then adjust by ear.
Apply it in TuningMac (parametric EQ)
TuningMac's Advanced EQ imports this format directly. Copy the settings, then:
- Open TuningMac ▸ Settings ▸ Advanced EQ with your SE112 connected.
- Turn on Use Advanced EQ for SE112 (or whatever you've named them on your Mac).
- Choose More ▸ Paste from Clipboard.
TuningMac saves it for your SE112 and loads it whenever they connect.
Preamp: -6.6 dB Filter 1: ON LSC Fc 105 Hz Gain 0.1 dB Q 0.70 Filter 2: ON PK Fc 182 Hz Gain -5.9 dB Q 0.68 Filter 3: ON PK Fc 6786 Hz Gain 7.1 dB Q 0.62 Filter 4: ON PK Fc 26 Hz Gain -0.2 dB Q 1.63 Filter 5: ON PK Fc 4572 Hz Gain -10.2 dB Q 5.32 Filter 6: ON HSC Fc 10000 Hz Gain 4.8 dB Q 0.70 Filter 7: ON PK Fc 842 Hz Gain 1.4 dB Q 1.93 Filter 8: ON PK Fc 2104 Hz Gain -1.9 dB Q 1.98 Filter 9: ON PK Fc 3086 Hz Gain 1.8 dB Q 3.24 Filter 10: ON PK Fc 8246 Hz Gain -1.8 dB Q 2.24
| # | Type | Frequency | Gain | Q |
|---|---|---|---|---|
| 1 | Low Shelf | 105 Hz | +0.1 dB | 0.70 |
| 2 | Bell | 182 Hz | −5.9 dB | 0.68 |
| 3 | Bell | 6.79 kHz | +7.1 dB | 0.62 |
| 4 | Bell | 26 Hz | −0.2 dB | 1.63 |
| 5 | Bell | 4.57 kHz | −10.2 dB | 5.32 |
| 6 | High Shelf | 10 kHz | +4.8 dB | 0.70 |
| 7 | Bell | 842 Hz | +1.4 dB | 1.93 |
| 8 | Bell | 2.1 kHz | −1.9 dB | 1.98 |
| 9 | Bell | 3.09 kHz | +1.8 dB | 3.24 |
| 10 | Bell | 8.25 kHz | −1.8 dB | 2.24 |
Preamp: −6.6 dB. It lowers the overall level so the boosts don't clip.
Prefer simple sliders? The 10-band version
No Advanced EQ needed: AutoEQ also gives values for a standard 10-band equalizer, the same bands as TuningMac's main EQ. In the menu bar popover choose Custom, set each slider, and set the preamp to about −11.0 dB.
Values in dB, at 31 Hz to 16 kHz. The parametric version above is more precise.
Questions
Do the Shure SE112 need a Bluetooth codec on a Mac?+
None: the SE112 are wired. Plug them into the Mac's headphone jack, or a USB-C adapter or DAC, and the sound reaches them without Bluetooth compression.
What are the best EQ settings for the Shure SE112?+
AutoEQ's correction, based on oratory1990's measurements, corrects a mid-treble dip around 4.6 kHz, adds about 7 dB around 6.8 kHz, with a preamp of -6.6 dB. The exact values are on this page, ready to copy. Treat it as a neutral starting point and adjust to taste.
Why do my Shure SE112 sound bad on calls on a Mac?+
When an app uses the earbuds' microphone, Bluetooth switches from stereo music mode to a hands-free call mode with much lower audio quality. To keep music quality during calls, choose your Mac's built-in microphone as the input instead. TuningMac's Input list does this in one click, and its Device Info shows which mode you're in.
Should I turn off the EQ in Shure's app?+
For the most accurate result, yes. An equalizer set in Shure's app is applied inside the earbuds, so it also affects your Mac and would add to this correction. TuningMac's EQ only changes sound from your Mac, so it won't affect your phone.
Tune your SE112 on your Mac
Parametric and 10-band EQ, noise control and battery in the menu bar.
EQ data from AutoEQ by Jaakko Pasanen (MIT licence), measurement by oratory1990. Specifications from Shure's published specifications. Shure SE112 is a trademark of Shure; TuningMac is not affiliated with Shure.